Home / Blog / Who Signs Off on a Backup Board Spec

Who Signs Off on a PCB Backup Board Specification

A backup board specification passes three gates before a pallet ships: process engineering sets the requirement, procurement sources against it, and quality releases the batch. They test the same sheet against three different measurements — which is why a board can be approved by one department and rejected by another in the same week.

Thickness is checked on a different grid from burr: four points per edge across three plies per board, with a ±0.15 mm declared band on the melamine range and 1.50 ±0.10 mm on the 3120 phenolic grade.

Flatness is a property of the sheet (≤0.10 mm on the phenolic grade, warp and twist ≤0.9%). Exit burr is not — it is a process output that stays at or below 0.05 mm only under qualified drilling conditions.

That split is the whole source of disagreement: two of those three numbers describe the material, one describes what the material does in your stack.

Who sets, sources and releases a backup board spec?

Three functions own three different decisions, and each one signs against a different document.

FunctionDecision they ownWhat they measure or readWhere it breaks
Process / CAM engineeringThe requirement: hole size, stack height, exit quality, smallest finished holeHole position (CPK and max deviation), hole-wall roughness, exit burr on the bottom panelThe sheet meets the drawing but the stack changed — more layers, thicker panel, different drill
ProcurementThe source and the commercial termsPrice per sheet, MOQ, sheet format and cut yield, lead time, MOQ per gradeTwo quotes look comparable until cut-to-size yield is included
Quality / IQCThe release of the batchThickness readings, hardness (Shore D), flatness, moisture, batch record and date codeThe sample was approved; the batch record is a different document with different readings

Why does the same sheet pass one gate and fail another?

Because the three gates do not measure the same thing, and only two of the three numbers are material constants.

Thickness and hardness are properties. Thickness is taken at four points along each edge, across three plies per board, and recorded as maximum, minimum and average — a distribution, not one reading. Hardness is read as Shore D on the same grid. Two boards can both be “in tolerance” and still differ by the full spread of the band.

Exit burr is a result. It moves with clamping, stack count, drill wear and entry-side choice, so a 0.05 mm figure quoted from one stack does not transfer to another. A quality engineer testing a coupon and a production engineer testing a live stack can reach opposite conclusions without either being wrong.

Class matters less than the hole. In third-party test data across seven board types, CPK at Ø0.15 mm runs from 2.395 on a 72 Shore D wood-fibre board to 4.700 on phenolic paper; at Ø0.35 mm every class lands between 1.68 and 1.82. Below Ø0.20 mm the grade carries the argument. Above Ø0.35 mm it does not.

What has to be in writing before the first order?

Three documents prevent most of the arguments, because each one answers a question a different department will ask later.

DocumentIt settlesMinimum fields
Specification sheet on the POWhat the supplier must shipGrade, construction, nominal thickness with tolerance, hardness class, flatness limit, sheet size, packing
Trial protocolWhat counts as a passDrill diameter, laminate and panel thickness, stack count, RPM and feed, hit count, entry board held constant, burr measurement position
Batch inspection recordWhat actually arrivedDate code, thickness max/min/average, hardness readings, flatness result, moisture result, pallet label matching the record

The trial protocol is the one that gets skipped. Without it, the sample is judged on a stack nobody wrote down, and the batch is judged against a memory of that stack.

How do you align the three before the order?

  1. Fix the grade from the smallest hole, not from the price. Below Ø0.20 mm start at the harder end (phenolic or high-density melamine); above Ø0.35 mm take the cheapest board that holds ≤0.10 mm flatness.
  2. Hold everything else constant in the first trial. Same drill bit, same entry board, same stack count, same parameters. Change one variable so the result means something.
  3. Ask for the batch record before the pallet, not after. A record you can compare against the spec sheet turns a claim into a measurement.
  4. State the tolerance basis. A ±0.15 mm band on a 2.5 mm board and ±0.10 mm on a 1.50 mm board are not the same starting point for a stack-height calculation.

Where this stops being a material question

If the sheet is stored above the recommended range, thickness readings drift before the drill ever touches it: the phenolic grade is specified at 5–40 °C and 50–80% RH with a 180-day shelf life, and water absorption is published at ≤2.0 g/200 cm². A warped sheet fails flatness inspection for reasons no grade selection can fix.

Equally, no backup board compensates for a stack that is already unstable. When burr concentrates on the bottom panel, the order of checks is clamping, stack count, drill wear, then the board — not the other way round.

What to send us

Send the current grade or a sample, the smallest finished hole, the stack count and the panel thickness. The reply is a grade-by-grade comparison against your reference and a sample cut from the same production batch — enough for all three departments to sign against the same document.

Send the specification Compare the grades →

← Back to Blog Request Sample Kit →
LX

Mr. Lucky Xu — Director, YUESHAN PCB — Director, YUESHAN PCB

15 years in PCB drilling consumables — the materials above and below the drilling stack. Wrote and technically reviewed this page. Figures come from YUESHAN production, incoming-inspection and field records; where a number is stated, the page says how it was measured, and any third-party or industry reference is named inline rather than presented as a YUESHAN specification.

About the author · Editorial standards & review process · Request TDS / SDS or a sample

Grade list and flatness limits are on the backup board range: HDF, melamine, UV-cured and phenolic.